Structural Steel Export Supplier From Malaysia: Cold-Formed Framing Cut and Punched to Your Member Schedule

Quick answer

At Powin Steel Industries Sdn Bhd we are a structural steel export supplier from Malaysia for overseas contractors, fabricators and importers who need cold-formed secondary steel. That means galvanised C and Z purlins, C-section roof trusses, battens and their fixings, roll-formed in our Melaka factory, cut to the lengths on your member schedule and pre-punched to your connection drawings. Your quotation is based on section, thickness, coating, quantities and punching. We do not supply hot-rolled beams or columns, so the primary frame comes from a separate supplier.

Key takeaways
  • Our galvanised C purlins come in 1.0, 1.6, 2.0, 2.5 and 3.0 mm thicknesses, with Z120, Z180, Z275 or Z350 zinc coating, in custom lengths made to order.
  • Our C-section roof trusses come in C-Section 135 and C-Section 153 profiles, 0.75–1.0 mm thick, with AZ70 or AZ150 aluminium-zinc coating, in a standard 6 m length.
  • We pre-punch holes to the size, position, spacing and layout on your project drawings, within product specifications and manufacturing tolerances.
  • An export order can include the fixings that go with the frame: purlin brackets, tie and sag rods, bolts and nuts, L brackets, screws and sleeve anchors.
  • Purlins and trusses carry a perforation warranty of up to 50 years, depending on the material specification and warranty terms.

This page explains what we can manufacture for a steel building being built outside Malaysia, how a drawing becomes a finished set of members, and what goes into the quotation. It also says plainly where another kind of supplier would suit your project better.

Stock-length steel shipped overseas gets cut and drilled a second time at the jobsite

The costly part of importing secondary steel is the rework at the destination, not the shipping. If purlins and trusses leave the factory in stock lengths without holes, your site crew has to measure, cut and drill every member. That means more labour, more offcuts and more chances for a hole to miss its cleat.

The risk grows with distance. If you discover a wrong end dimension or a member punched from an old drawing revision after the container is unpacked, you cannot simply reorder it from down the road. Two purlins with the same section can still need different end holes, laps or lengths. If the order does not tell them apart, the mistake is repeated on every member of that mark.

Technical drawings and project specifications reviewed before a steel framing order
Before production we check your drawings and specifications, so lengths and holes are settled before any steel is formed.

One Melaka roll-forming line makes the whole secondary frame: purlins, C-section trusses, battens and fixings

We roll-form, cut and punch the members in-house, so one factory takes your schedule all the way to finished, ready-to-fix pieces. Here is how an export order runs and what you receive at each stage:

  1. Drawing and schedule review. You send the approved framing layout, member schedule and connection details. Our technical drawing and project guidance support checks that each member mark has a profile, cut length, hole layout, quantity and current revision. You get a list of any gaps to close before we quote.
  2. Section and coating confirmed per mark. For example, a C purlin from 1.0 to 3.0 mm in Z120 to Z350 galvanising, or a C-section truss in profile 135 or 153 with AZ70 or AZ150 coating. You receive a quotation broken down by member mark.
  3. Roll-forming and cut-to-length. We form the members in Melaka and cut each one to its finished length, not to a stock length you would have to trim.
  4. Pre-punching. We punch circular or slotted holes to your specified sizes, positions and spacing, so the members bolt straight to brackets and cleats.
  5. Fixings packed with the frame. Purlin brackets, tie and sag rods and bolts and nuts for purlin systems, plus G.I. L brackets, screws and sleeve anchors for trusses, can go on the same order.
Galvanised C and Z purlins made by Powin Steel, a structural steel export supplier from Malaysia
Galvanised C and Z purlins from our Melaka line, made to custom lengths with project-specific punching.
Custom purlin punching with circular and slotted hole configurations
Hole size, position, spacing and layout follow your connection drawings.
Galvanised C-section steel roof truss members
C-section roof truss members in profile 135 or 153, supplied in a standard 6 m length.

For a full checklist of the punching details we need (datums, end distances, reference faces and laps), see our drawing guide for pre-punched purlins. If the same building also needs roof sheeting, our metal roofing for export page covers the Metal Deck 762, Clip Lock, High Rib and Uroll Bond profiles we can quote with the frame.

Send us your member schedule and get a quotation broken down by mark

Share your framing drawings and schedule on WhatsApp or through our enquiry form. We will review each member, flag anything missing, and quote by section, coating, length and punching.

Thickness, coating and the member schedule set the price of an export order

Your export quotation is built from your schedule, line by line. The biggest factors are steel thickness, coating class, the number of members per mark and how much punching each one needs. Here is how each choice affects the price:

Cost factorOptions we manufactureHow it affects the quotation
Purlin thickness1.0 / 1.6 / 2.0 / 2.5 / 3.0 mmThicker sections use more steel per metre, so they cost more per metre.
Purlin zinc coatingZ120 / Z180 / Z275 / Z350A heavier zinc class raises the material cost and is chosen to suit the site's exposure.
Truss profile and coatingC-Section 135 or 153; 0.75–1.0 mm; AZ70 / AZ150The profile and coating class set the unit price per standard 6 m member.
LengthsPurlins custom made to orderMembers are cut to finished length, so you pay for the lengths you will install, without offcuts.
PunchingCustom hole size, position, spacing and layoutEach distinct hole pattern is set up per member mark, and repeated marks are more efficient to produce.
FixingsBrackets, tie/sag rods, bolts and nuts, L brackets, screws, anchorsQuoted as line items so the frame arrives with its fixings.

In practice, a complete schedule with revision-controlled punching details gets a firm quotation fastest. A layout without hole details can only be priced as plain cut-to-length members. Freight to your destination port is not part of the factory price, so tell us the destination when you enquire and we will confirm how delivery can be arranged.

Product drawing of a C-section steel roof truss
Our published C-section truss drawing, a reference for checking the profile against your design.

Cold-formed members from our factory vs hot-rolled sections or stock lengths from a steel trader

We are the right source for the secondary frame: purlins, girts, trusses and battens, cut and punched to your schedule. We are not the right source for the primary frame of universal beams and columns. Most steel buildings need both, and a buyer comparing Malaysian suppliers is usually weighing these three routes:

Point of comparisonPowin Steel (cold-formed, made to order)Hot-rolled steel traderStock-length purlins, finished at the destination
What it coversGalvanised C and Z purlins, C-section trusses, battens and fixingsBeams, columns, angles, plates for the primary framePlain stock-length purlins and channels
LengthsCustom lengths cut to your scheduleMill or stock lengths, often cut on requestStock lengths, trimmed on site
Connection holesPre-punched to your drawingsUsually fabricated by a separate shopDrilled by the site crew
Corrosion protectionZ120–Z350 galvanising or AZ70/AZ150 aluminium-zinc coating at the sourceVaries, often painted or galvanised after fabricationHoles drilled on site cut through the existing coating
Best fitRoof and wall framing for factories, warehouses, commercial buildings, shoplots and farmsHeavy primary structure, bridges, large spansSmall jobs with simple, repetitive framing

If your design calls for heavy hot-rolled sections, buy those from a mill trader and give us the secondary framing schedule. For a broader view of everything we ship, from purlins to roofing, see our page on exporting steel building materials.

Powin Steel: roll-forming galvanised framing in Melaka since 2009

At Powin Steel Industries Sdn Bhd, we have manufactured steel building materials since 2009 from our factory in Kawasan Perindustrian Cheng, Melaka. What matters for an export frame is that we form, cut and punch in-house, so your schedule never passes between a mill, a cutter and a separate punching shop.

Powin Steel factory in Melaka where purlins and trusses are roll-formed
Our Melaka factory, where every member on your schedule is formed, cut and punched.
  • We make the full secondary frame in one place: C and Z purlins for export, steel roof trusses for export, battens and fixings.
  • Our production planning works from your member schedule, so lengths and punching are fixed before forming starts.
  • We offer project support with technical drawings, product guidance and coordination of installation arrangements when needed.
  • We have supplied more than 1,000 customers and delivered to over 50,000 sites across Malaysia.

Proof from our customers and factory records

Here is what we can show you before you place an export order:

"Satisfied with the product quality and service provided. Delivery was arranged properly and on schedule."

Raymond Chin, client review on our website

"Good quality purlin and roofing materials. The team provides fast response and helpful product recommendations."

Leslie, client review on our website

Powin Steel project reference in Ulu Tiram, Johor
Project reference: Ulu Tiram, Johor.
Powin Steel project reference in Kuala Pahang, Pekan
Project reference: Kuala Pahang, Pekan.
  • Purlins and trusses carry a perforation warranty of up to 50 years, depending on the selected material specification and terms. Ask us for the terms that apply to your coating class.
  • Our published product specifications are dated (September 2026), so you can check the thicknesses and coatings you are quoting against.

Powin Steel Industries Sdn Bhd, 200901035320 (878436-W), PT 4824, Jalan TTC 33, Kawasan Perindustrian Cheng, 75250 Melaka.

Questions from overseas buyers

No. We manufacture cold-formed galvanised members: C and Z purlins, C-section roof trusses and battens, plus their fixings. The hot-rolled primary frame should come from a mill or steel trader, and we supply the secondary framing that fixes onto it.
For each member mark: the profile (C or Z), section dimensions and thickness, material and coating, finished cut length with its measuring reference, the hole layout drawing, quantity and current drawing revision. Our C and Z purlin range lists the thicknesses and coatings to choose from.
Your project's appointed engineer remains responsible for final connection design and structural adequacy. We manufacture to the approved drawings, help with drawings and specifications, and flag inconsistencies we find in the schedule before production.
Yes. We supply purlin brackets, tie and sag rods and bolts and nuts for purlin systems, and G.I. L brackets, screws and sleeve anchors for truss systems, quoted as line items on the same order. Our roofing accessories range covers the remaining roof components.
C-section trusses are supplied in a standard 6 m length in profile 135 or 153, 0.75–1.0 mm thick, with AZ70 or AZ150 coating. C and Z purlins, by contrast, are cut to whatever finished length your schedule specifies.

Get a frame that arrives ready to bolt up, without cutting or drilling on site

Send your framing layout and member schedule on WhatsApp or through our enquiry form. Our team will check each mark, list any missing details, and send a quotation broken down by section, coating, length, punching and fixings, with your destination noted so delivery can be discussed.

Contact Us Now
JACKON
MIA
LILY